Hi,
has just started using Dalsight 4 in an installation.
Everything works great - except a couple of cheap china moving heads I can't get to function correct.
The fixture profile that comes with the lights are not correct, so I made one myselt in the previous software I used.
The problem: when I create i profile for the fixture, I can get the pan/tilt to work fine using the faders - but the grid in the palette triggers uPan and uTilt.
Tried several different configurations but I'm stuck.
Tthe profile starts with
1 - PAN
2- uPan
3 - TILT
4 - uTilt
I'm a little hurry since I need to use the fixtures this friday. So please, if know, help me
Regards
/daniel
PAN / TILT problems
Re: PAN / TILT problems
Hi again,
is it possible to get support here ? Or should I contact you (Daslight) some other way?
/daniel
is it possible to get support here ? Or should I contact you (Daslight) some other way?
/daniel
Re: PAN / TILT problems
Hello,
Sorry about the delay. I'm not sure I understand what the problem is exactly.
Regards,
Sorry about the delay. I'm not sure I understand what the problem is exactly.
Do you mean that the grid only triggers uPan and uTilt ? And no Pan, no Tilt ?Pustervik wrote:I can get the pan/tilt to work fine using the faders - but the grid in the palette triggers uPan and uTilt
Regards,
TomHat
--
Daslight Support
Mail : [email protected]
Phone (French) : +33 (0) 616 427 588
Phone (English) : +44 (0) 7 481 811 500
--
Daslight Support
Mail : [email protected]
Phone (French) : +33 (0) 616 427 588
Phone (English) : +44 (0) 7 481 811 500
Re: PAN / TILT problems
Hi,
I think I have the same problem. I have moving heads in 16 channel mode and the first four channels are:
1–Pan
2-Fine Pan
3-Tilt
4-Fine Tilt
When I manipulate the faders attached to Pan and Tilt the fixture Pans and Tilts normally, but if I use the Pan/Tilt palette the fixture only moves as if Fine Pan & Fine Tilt are being moved. When I check the fader page for the fixture it shows non zero values for channels 2 and 4, but 0 on channels 1 and 3.
Screenshots and ssl2 attached.
I think I have the same problem. I have moving heads in 16 channel mode and the first four channels are:
1–Pan
2-Fine Pan
3-Tilt
4-Fine Tilt
When I manipulate the faders attached to Pan and Tilt the fixture Pans and Tilts normally, but if I use the Pan/Tilt palette the fixture only moves as if Fine Pan & Fine Tilt are being moved. When I check the fader page for the fixture it shows non zero values for channels 2 and 4, but 0 on channels 1 and 3.
Screenshots and ssl2 attached.
- Attachments
-
- Screen Shot 2018-11-20 at 5.47.42 PM.png (191.47 KiB) Viewed 8522 times
-
- Screen Shot 2018-11-20 at 5.47.50 PM.png (254.79 KiB) Viewed 8522 times
-
- Totem China.ssl2.zip
- (21.9 KiB) Downloaded 325 times
Re: PAN / TILT problems
Hello Malachy,
Does this file fix your problem ?
Pustervik, could you please send me your SSL file ?
Regards,
Does this file fix your problem ?
Pustervik, could you please send me your SSL file ?
Regards,
TomHat
--
Daslight Support
Mail : [email protected]
Phone (French) : +33 (0) 616 427 588
Phone (English) : +44 (0) 7 481 811 500
--
Daslight Support
Mail : [email protected]
Phone (French) : +33 (0) 616 427 588
Phone (English) : +44 (0) 7 481 811 500
Re: PAN / TILT problems
Hi,
sorry if I was not clear - but it's exactly the same problem.
Attached the file - it's not complete since I never got the pan/tilt to work properly.
All best
/daniel
sorry if I was not clear - but it's exactly the same problem.
Attached the file - it's not complete since I never got the pan/tilt to work properly.
All best
/daniel
- Attachments
-
- chinabeam.zip
- (7.03 KiB) Downloaded 315 times
Re: PAN / TILT problems
Hi again,
I attached the manufacturers fixture profile.
The colour wheel is not correct by I have found the correct numbers
all best
/daniel
I attached the manufacturers fixture profile.
The colour wheel is not correct by I have found the correct numbers
all best
/daniel
- Attachments
-
- IMG_8749-1.jpg (90.05 KiB) Viewed 8504 times
-
- IMG_8750-1.jpg (83.38 KiB) Viewed 8504 times
-
- IMG_8751-1.jpg (90.95 KiB) Viewed 8504 times
Re: PAN / TILT problems
Hello,
This should work better. It does for me. Although, I'm not sure you guys had the same problem, now when I have seen both SSL files.
Pustervik, the Pan/Tilt grid should act on all 4 channels : Pan/uPan/Tilt/uTilt
Regards,
This should work better. It does for me. Although, I'm not sure you guys had the same problem, now when I have seen both SSL files.
Pustervik, the Pan/Tilt grid should act on all 4 channels : Pan/uPan/Tilt/uTilt
Regards,
- Attachments
-
- chinabeam.zip
- (7.07 KiB) Downloaded 353 times
TomHat
--
Daslight Support
Mail : [email protected]
Phone (French) : +33 (0) 616 427 588
Phone (English) : +44 (0) 7 481 811 500
--
Daslight Support
Mail : [email protected]
Phone (French) : +33 (0) 616 427 588
Phone (English) : +44 (0) 7 481 811 500
Re: PAN / TILT problems
Thanks!
The big problem was pan/tilt speed. And the default setting on that channel.
Now everything works great!
The big problem was pan/tilt speed. And the default setting on that channel.
Now everything works great!